Class 12 PCB . Physics . Physics Part I . Current Electricity

Chapter 3: Current Electricity

Ch 3

Physics

Class 12 PCB

Lecture 1

Introduction

Reference video · Lecture 1Introduction

Electric Current: Overview

  • Electric current is the flow of electric charge; charges in motion produce current.
  • Steady and unsteady flow: Lightning carries an unsteady current, while devices such as torches and cell-driven clocks use steady current.
  • Chapter focus: The chapter studies the basic laws of steady electric currents.

Electric Current

Definition

Electric current — The net charge crossing a conductor’s cross-section per unit time.

  • Net charge: For steady flow, the net forward charge accounts for positive and negative charges crossing the area in either direction.
  • Sign: A negative current value means the actual current is opposite to the chosen positive direction.
  • Direction convention: Current direction is the direction of positive charge flow; in metals, electrons drift in the opposite direction.
I=qtI=\frac{q}{t}
For steady current:
I(t)=lim⁡Δt→0ΔQΔtI(t)=\lim_{\Delta t\to 0}\frac{\Delta Q}{\Delta t}
For a time-varying current:
  • Symbols: qq is the net charge in time tt; Q is the net charge crossing during a small interval t.
  • SI unit: The ampere (A) is defined through the magnetic effects of current.
  • Typical magnitudes: Domestic-appliance currents are of order amperes; lightning currents are tens of thousands of amperes; nerve currents are in microamperes.

Electric Currents in Conductors

Definition

Conductor — A material containing charges free to move through it, allowing current when an electric field is applied.

  • Electric field: A free charge experiences a force and moves when an electric field is applied.
  • Conductors and insulators: In metals, some electrons can move through the material; in other materials, electrons remain bound and do not move freely.
  • Solid conductors: Current is carried by mobile electrons moving among fixed positive ions.
  • Other conductors: In electrolytic solutions, both positive and negative charges can move.
Conductor Without and With an Electric Field
ConditionCharge motionNet current
No electric fieldElectrons move thermally and collide with ions; their directions are random.Zero on average, because opposite directions balance.
Electric field appliedElectrons accelerate opposite to the field, but collisions disrupt their motion.A net current results from their overall drift.
  • Temporary current: If charges are placed at the conductor’s ends, the resulting field moves electrons and briefly produces current; the current stops when the end charges are neutralised.
  • Steady current: Cells or batteries replenish charges and maintain a steady electric field, sustaining current.

Ohm’s Law and Resistance

Definition

Ohm’s law — For a conductor, the potential difference across its ends is proportional to the current through it.

V=IRV=IR
Ohm’s law:
  • Resistance (RR): The proportionality constant between potential difference and current; SI unit is the ohm (Ω\Omega).
  • G. S. Ohm: Formulated the law in 1828.
  • Dependence: Resistance depends on the conductor’s material and dimensions.
R∝l,R∝1A,R=ρlAR\propto l,\qquad R\propto\frac{1}{A},\qquad R=\rho\frac{l}{A}
Resistance increases with length and decreases with cross-sectional area:
  • Length effect: Doubling the conductor’s length doubles its resistance.
  • Area effect: Halving its cross-sectional area doubles its resistance.
  • Resistivity (ρ\rho): A material property independent of the conductor’s dimensions; its SI unit is Ω m\Omega\,\text{m}.

Current Density and Conductivity

Definition

Current density — Current per unit area measured on a cross-section normal to the current.

j=IAj=\frac{I}{A}
For a uniform current through area AA:
  • SI unit: Current density is measured in A/m2\text{A}/\text{m}^2.
  • Field and potential difference: For a uniform electric field along a conductor of length ll, the potential difference is V=ElV=El.
  • Conductivity (σ\sigma): The reciprocal of resistivity, so σ=1/ρ\sigma=1/\rho; its SI unit is S/m\text{S}/\text{m}.
E⃗=ρj⃗,j⃗=σE⃗\vec{E}=\rho\vec{j},\qquad \vec{j}=\sigma\vec{E}
Vector form of Ohm’s law:
  • Direction: In an ohmic conductor, current density and electric field point in the same direction.
  • Equivalent forms: Ohm’s law can be written as V=IRV=IR for a whole conductor or j⃗=σE⃗\vec{j}=\sigma\vec{E} locally.

State Ohm’s law and define resistance.

Answer: Ohm’s law states that V∝IV\propto I, or V=IRV=IR. Resistance RR is the proportionality constant and is measured in ohms (Ω\Omega).

How does a conductor’s resistance depend on its dimensions and material?

Answer: R=ρl/AR=\rho l/A: resistance is proportional to length, inversely proportional to cross-sectional area, and depends on the material through resistivity ρ\rho.

Quick recap

  • Current is the net charge crossing a cross-section per unit time; its SI unit is the ampere.
  • Without an electric field, random thermal electron motion produces no net current.
  • A steady electric field, maintained by a cell or battery, sustains current in a conductor.
  • Ohm’s law is V=IRV=IR; resistance is measured in ohms.
  • Resistance follows R=ρl/AR=\rho l/A, where resistivity depends on the material.
  • Current density is j=I/Aj=I/A, and the local law is j⃗=σE⃗\vec{j}=\sigma\vec{E}.
Lecture 2

Drift of Electrons and the Origin of Resistivity

Reference video · Lecture 2Drift of Electrons and the Origin of Resistivity

Electron motion and drift velocity

Electron motion in an electric field

  • Random motion: Without an electric field, collisions with heavy ions scatter electrons in random directions, so their average velocity is zero: 1N∑i=1Nv⃗i=0\frac{1}{N}\sum_{i=1}^{N}\vec{v}_i=0.
  • Acceleration: An electron of charge −e-e and mass mm in an electric field has acceleration a⃗=−emE⃗\vec{a}=-\frac{e}{m}\vec{E}.
  • Between collisions: If an electron's velocity immediately after its last collision is v⃗i\vec{v}_i, and the time since then is tit_i, its velocity is V⃗i=v⃗i−emE⃗ti\vec{V}_i=\vec{v}_i-\frac{e}{m}\vec{E}t_i.
  • Relaxation time (τ\tau): The average time between successive collisions; collisions occur at irregular intervals. The average time elapsed since the last collision, across the electrons, is also taken as τ\tau.
Drift velocity
v⃗d=−eτmE⃗\vec{v}_d=-\frac{e\tau}{m}\vec{E}

The random velocities average to zero, but the field-driven velocity produces a steady average drift opposite to the electric field.

Meaning of drift

  • Individual electrons: They accelerate between collisions; collisions interrupt their acceleration, so their average motion is a small, steady drift.
  • Direction: Electron drift is opposite to E⃗\vec{E}; electrons move toward higher electric potential.
  • Paths: Between collisions, paths are straight without a field and generally curved when a field is present.
Electron path between collisions; net drift is opposite to the applied electric field.
Electron path between collisions; net drift is opposite to the applied electric field.

Current and conductivity

Charge transport and current density

  • Electrons crossing area: In time Δt\Delta t, electrons within distance ∣vd∣Δt|v_d|\Delta t of a plane of area AA cross it. For number density nn, their number is nA∣vd∣ΔtnA|v_d|\Delta t.
  • Current magnitude: Each electron has charge magnitude ee, so IΔt=neA∣vd∣ΔtI\Delta t=neA|v_d|\Delta t and I=neA∣vd∣I=neA|v_d|.
  • Current density: I=∣j⃗∣AI=|\vec{j}|A. Conventional current density is parallel to E⃗\vec{E} and opposite to the electron drift.
A metallic conductor showing the electric field and electron drift.
A metallic conductor showing the electric field and electron drift.
Current density and conductivity
j⃗=ne2τmE⃗,σ=ne2τm\vec{j}=\frac{ne^2\tau}{m}\vec{E},\qquad \sigma=\frac{ne^2\tau}{m}

The microscopic relation between current density and electric field reproduces Ohm's law.

Origin of resistivity

  • Conductivity: The model gives σ=ne2τm\sigma=\frac{ne^2\tau}{m}, so it depends on the carrier density nn and average collision time τ\tau.
  • Role of collisions: Collisions with metal ions interrupt electron acceleration and limit drift, giving the conductor finite conductivity and resistivity.
  • Assumptions: The derivation treats nn and τ\tau as constants independent of the applied electric field.

Example: Drift speed in a copper wire

Estimate and comparisons

  • Given: I=1.5 AI=1.5\,\text{A}, A=1.0×10−7 m2A=1.0\times10^{-7}\,\text{m}^2, copper density 9.0×103 kg/m39.0\times10^3\,\text{kg/m}^3, and atomic mass 63.5 u63.5\,\text{u}. Assume one conduction electron per copper atom.
  • Electron density: Using the mass per copper atom gives n≈8.5×1028 m−3n\approx8.5\times10^{28}\,\text{m}^{-3}.
  • Drift speed: From vd=IneAv_d=\frac{I}{neA}, the estimate is vd≈1.1×10−3 m/s=1.1 mm/sv_d\approx1.1\times10^{-3}\,\text{m/s}=1.1\,\text{mm/s}.
  • Thermal-speed relation: For an atom of mass MM at temperature TT, ⟨12Mv2⟩=32kBT\left\langle\frac{1}{2}Mv^2\right\rangle=\frac{3}{2}k_BT; hence a typical speed is of order kBTM\sqrt{\frac{k_BT}{M}}.
  • Thermal comparison: For copper at 300 K300\,\text{K}, the typical atomic thermal speed is about 2×102 m/s2\times10^2\,\text{m/s}; the drift speed is about 10−510^{-5} as large.
  • Field-propagation comparison: The electric field propagates along the conductor at about 3.0×108 m/s3.0\times10^8\,\text{m/s}, roughly 101110^{11} times the drift speed.

How can current begin almost immediately if electron drift is very slow?

Answer: The electric field is established throughout the circuit rapidly, causing local electron drift throughout it. Electrons do not need to travel from one end of the conductor to the other first; the current may take a little time to reach its steady value.

Why can a conductor carry a large current despite the small drift speed of its electrons?

Answer: The number density of conduction electrons is enormous, about 1029 m−310^{29}\,\text{m}^{-3}. Drift is superposed on the electrons' large random velocities, so not all electrons move in the same direction overall.

What are electron paths between collisions with and without an electric field?

Answer: Without an electric field, paths are straight between collisions; with a field, they are generally curved.

Mobility

Definition

Mobility — Mobility is the magnitude of drift velocity per unit electric field.

Electron mobility
μ=∣v⃗d∣E=eτm\mu=\frac{|\vec{v}_d|}{E}=\frac{e\tau}{m}

Mobility is positive; the vector direction of electron drift is specified separately. Its SI unit is m2/(V s)\text{m}^2/(\text{V}\,\text{s}), with 1 m2/(V s)=104 cm2/(V s)1\,\text{m}^2/(\text{V}\,\text{s})=10^4\,\text{cm}^2/(\text{V}\,\text{s}).

Mobile charge carriers

  • Metals: Electrons are the mobile charge carriers.
  • Ionised gases: Electrons and positive ions are mobile carriers.
  • Electrolytes: Both positive and negative ions can carry charge.

Quick recap

  • Random electron velocities average to zero, while an electric field produces drift opposite to the field.
  • The average electron drift velocity is v⃗d=−eτmE⃗\vec{v}_d=-\frac{e\tau}{m}\vec{E}; collisions limit its value.
  • Current magnitude is I=neA∣vd∣I=neA|v_d|, and conventional current density is parallel to the electric field.
  • The model reproduces Ohm's law: j⃗=σE⃗\vec{j}=\sigma\vec{E}, where σ=ne2τm\sigma=\frac{ne^2\tau}{m}.
  • Copper-wire drift is very slow, but the carrier density is huge and the electric field is established rapidly.
  • Mobility is μ=∣v⃗d∣E=eτm\mu=\frac{|\vec{v}_d|}{E}=\frac{e\tau}{m} for electrons.
Lecture 3

Limitations of Ohm’s Law

Reference video · Lecture 3Limitations of Ohm’s Law

Limitations of Ohm’s Law

Ways the voltage–current relation can deviate

  • Non-proportionality: Voltage VV may cease to be proportional to current II; the VV–II graph is then non-linear.
  • Polarity dependence: Reversing VV need not produce an equal current in the opposite direction; a diode is an example.
  • Non-unique relation: The same current II can correspond to more than one voltage VV; GaAs devices can show this behaviour.
  • Use: Many non-ohmic materials and devices are useful in electronic circuits, even though this lecture focuses on ohmic materials.
A good conductor has an approximately linear V–I relation; its actual curve can depart from the ideal Ohm’s law line.
A good conductor has an approximately linear VV–II relation; its actual curve can depart from the ideal Ohm’s law line.
A diode’s current–voltage characteristic differs for positive and negative bias.
A diode’s current–voltage characteristic differs for positive and negative bias.
A GaAs device can have multiple voltages for the same current, including a negative-resistance region.
A GaAs device can have multiple voltages for the same current, including a negative-resistance region.

Resistivity of Materials

Definition

Resistivity — A material property that indicates how strongly the material opposes electric current; materials are classified by increasing resistivity as conductors, semiconductors and insulators.

Material classes by resistivity
ClassTypical resistivity / behaviourExamples or importance
ConductorsMetals: about 10−810^{-8} to 10−6 Ω m10^{-6}\,\Omega\,\mathrm{m}Low resistivity
SemiconductorsIntermediate resistivity; resistivity generally decreases as temperature risesAdding a small amount of suitable impurity can lower resistivity
InsulatorsVery high resistivity; ceramic, rubber and plastics may be 101810^{18} times more resistive than metals or moreStrongly oppose current

Temperature Dependence of Resistivity

Resistivity near a reference temperature
ρT=ρ0[1+α(T−T0)]\rho_T = \rho_0[1 + \alpha(T - T_0)]

For a limited temperature range, resistivity is approximately linear in temperature. Here, ρT\rho_T is resistivity at TT, and ρ0\rho_0 is resistivity at reference temperature T0T_0.

Temperature coefficient

  • Coefficient: α\alpha is the temperature coefficient of resistivity; its dimension is inverse temperature, [α]=K−1[\alpha]=\mathrm{K}^{-1}.
  • Metals: α\alpha is positive, so resistivity generally rises with temperature.
  • Range: The linear relation is approximate over a limited range around T0T_0; at temperatures far below 0∘C0^\circ\mathrm{C}, metals can depart considerably from linearity.
Copper resistivity increases approximately linearly with temperature over the shown range.
Copper resistivity increases approximately linearly with temperature over the shown range.
Temperature response of materials
MaterialChange in resistivity with temperatureSignificance / example
NichromeVery weak increaseNickel–iron–chromium alloy; used in wire-wound standard resistors
Manganin and constantanVery weak temperature dependenceResistance changes little with temperature, making them useful for standard resistors
SemiconductorsResistivity decreases as temperature risesOpposite trend to metals
Nichrome resistivity changes only slightly as absolute temperature increases.
Nichrome resistivity changes only slightly as absolute temperature increases.
Semiconductor resistivity falls as temperature increases.
Semiconductor resistivity falls as temperature increases.
Microscopic relation for resistivity
ρ=1σ=mne2τ\rho = \frac{1}{\sigma} = \frac{m}{ne^2\tau}

Resistivity depends inversely on free-electron number density nn and mean time between collisions τ\tau.

Why resistivity changes with temperature

  1. Heating: Carrier speed rises, causing more frequent collisions and reducing τ\tau.
  2. Metals: The number density nn changes negligibly, so the fall in τ\tau makes ρ\rho increase.
  3. Semiconductors and insulators: nn increases with temperature; this effect outweighs the reduced τ\tau, so ρ\rho decreases.

Applications of Temperature Dependence

Finding a heated resistor’s temperature

  1. Find the steady resistance from the supply voltage and steady current.
    R2=VI=2302.68=85.8 ΩR_2 = \frac{V}{I} = \frac{230}{2.68} = 85.8\,\Omega
  2. Use the resistance–temperature relation to find the temperature rise.
    T2−T1=R2−R1αR1=85.8−75.3(1.70×10−4)(75.3)=820∘CT_2 - T_1 = \frac{R_2 - R_1}{\alpha R_1} = \frac{85.8 - 75.3}{(1.70\times10^{-4})(75.3)} = 820^\circ\mathrm{C}
  3. Add the rise to the initial temperature; the toaster element reaches approximately 847∘C847^\circ\mathrm{C}.
    T2=27.0+820=847∘CT_2 = 27.0 + 820 = 847^\circ\mathrm{C}

Toaster example: key interpretation

  • Given: Nichrome has R1=75.3 ΩR_1=75.3\,\Omega at T1=27.0∘CT_1=27.0^\circ\mathrm{C} and average α=1.70×10−4 ∘C−1\alpha=1.70\times10^{-4}\, ^\circ\mathrm{C}^{-1}.
  • Steady state: Heating raises the element’s resistance, lowering its current until heat produced balances heat lost to the surroundings.
Resistance thermometer temperature
t=Rt−R0R100−R0×100t = \frac{R_t-R_0}{R_{100}-R_0}\times100

For a platinum thermometer calibrated at the ice point and steam point, use the resistance ratio to determine temperature tt in Celsius.

Platinum thermometer example

  • Calibration: R0=5 ΩR_0=5\,\Omega at the ice point, R100=5.23 ΩR_{100}=5.23\,\Omega at the steam point, and bath resistance Rt=5.795 ΩR_t=5.795\,\Omega.
  • Calculation: t=5.795−55.23−5×100=345.65∘Ct=\frac{5.795-5}{5.23-5}\times100=345.65^\circ\mathrm{C}.
  • Alternative relation: For a linear resistance thermometer, Rt=R0(1+αt)R_t=R_0(1+\alpha t).

State three ways in which a device can deviate from Ohm’s law.

Answer: The VV–II relation may be non-proportional, depend on the sign of VV, or be non-unique so that one current corresponds to multiple voltages.

Why does metallic resistivity increase with temperature while semiconductor resistivity decreases?

Answer: Heating reduces the collision time τ\tau. In metals, carrier density nn remains nearly constant, so resistivity rises. In semiconductors, nn increases enough to outweigh the effect of reduced τ\tau, so resistivity falls.

Quick recap

  • Ohm’s law can fail through non-linearity, polarity dependence or a non-unique voltage–current relation.
  • Materials are ordered by increasing resistivity as conductors, semiconductors and insulators.
  • Near a reference temperature, resistivity follows ρT=ρ0[1+α(T−T0)]\rho_T=\rho_0[1+\alpha(T-T_0)] over a limited range.
  • Metal resistivity generally increases with temperature; semiconductor and insulator resistivity generally decreases.
  • Nichrome, manganin and constantan have weak temperature dependence and are suitable for standard resistors.
  • Resistance thermometers use the change in resistance with temperature to determine an unknown temperature.
Lecture 4

Electrical Energy, Power

Reference video · Lecture 4Electrical Energy, Power

Electrical Energy in a Conductor

Energy transfer

  • Potential drop: If current II flows from AA to BB, then V(A)>V(B)V(A)>V(B) and the potential difference is V=V(A)−V(B)>0V=V(A)-V(B)>0.
  • Charge transferred: In time Δt\Delta t, the charge moving through the conductor is ΔQ=IΔt\Delta Q=I\Delta t.
  • Potential energy change: The charge loses potential energy: ΔUpot=−ΔQV=−IVΔt\Delta U_{\text{pot}}=-\Delta QV=-IV\Delta t.
  • Free charge carriers: Without collisions, conservation of energy gives ΔK=−ΔUpot=IVΔt>0\Delta K=-\Delta U_{\text{pot}}=IV\Delta t>0; their kinetic energy would increase.
  • Collisions: In a real conductor, charge carriers collide with atoms and ions, transferring their gained energy to them; the conductor heats up.
  • Heat dissipated: In time Δt\Delta t, the electrical energy converted to heat is ΔW=IVΔt\Delta W=IV\Delta t.

Electrical Power and Power Transmission

Definition

Electrical power — The rate at which electrical energy is dissipated or transferred in a circuit.

Power dissipated in a resistor
P=IV=I2R=V2RP=IV=I^2R=\frac{V^2}{R}

Use the form that matches the known quantities. Power lost as heat in a resistor is called ohmic loss.

Meaning and source of power

  • Unit: Power is measured in watts (W\mathrm{W}).
  • Heating effect: Power dissipated in a bulb’s filament heats it to incandescence, producing heat and light.
  • Energy source: An external source maintains steady current and supplies the electrical power; in a cell, this energy comes from chemical energy.
A cell supplies energy that is dissipated as heat in a resistor.
A cell supplies energy that is dissipated as heat in a resistor.

Power loss in transmission cables

  • Useful power: A device operating at voltage VV and current II receives power P=VIP=VI.
  • Cable loss: For cable resistance RcR_c, the wasted power is Pc=I2RcP_c=I^2R_c.
  • High-voltage transmission: At fixed delivered power, raising VV reduces current and cable loss, since PcP_c varies inversely with V2V^2.
  • Safety: Transmission lines use very high voltages to limit losses; transformers lower the voltage before electricity is used safely.
Cable power loss
Pc=I2Rc=P2RcV2P_c=I^2R_c=\frac{P^2R_c}{V^2}

For a device receiving power PP at voltage VV, connected through cables of resistance RcR_c.

Cells, EMF and Internal Resistance

Definition

Electromotive force (emf) — The potential difference between a cell’s positive and negative electrodes when no current flows.

Cell terminals and emf

  • Cell structure: A cell has positive and negative electrodes immersed in an electrolyte; the electrodes exchange charges with it.
  • Electrode potentials: The positive electrode is at potential V+V_+ relative to nearby electrolyte; the negative electrode is at −V−-V_-.
  • Open circuit: With no current, the electrolyte is at the same potential throughout, so the electrode potential difference is ε=V++V−>0\varepsilon=V_++V_->0.
  • Terminology: Despite its name, emf is a potential difference, not a force.
Cell electrodes and the circuit symbol.
Cell electrodes and the circuit symbol.
Definition

Internal resistance — The resistance rr of the electrolyte to current flow through a cell.

Terminal voltage and current

  • Open circuit: When external resistance is effectively infinite, current is zero and terminal voltage equals emf: V=εV=\varepsilon.
  • Closed circuit: When current II flows, some potential difference is lost across internal resistance, so terminal voltage is V=ε−IrV=\varepsilon-Ir.
  • External resistor: Across an external resistance RR, Ohm’s law gives V=IRV=IR.
  • Cell current: Combining the terminal-voltage relation with Ohm’s law gives I=εR+rI=\frac{\varepsilon}{R+r}.
  • Negligible internal resistance: The effect of rr may be ignored when ε≫Ir\varepsilon\gg Ir.
  • Cell types: Dry cells generally have much higher internal resistance than common electrolytic cells.
Terminal voltage and cell current
V=ε−Ir=IR,I=εR+rV=\varepsilon-Ir=IR,\qquad I=\frac{\varepsilon}{R+r}

For emf ε\varepsilon, internal resistance rr, and external resistance RR.

Maximum current

  • Short-circuit limit: The maximum current occurs when R=0R=0, giving Imax⁡=εrI_{\max}=\frac{\varepsilon}{r}.
  • Practical limit: Cells usually allow a much smaller current to prevent permanent damage.

Why is electrical power transmitted at high voltage?

Answer: For fixed delivered power, higher voltage means lower current. Since cable loss is Pc=I2Rc=P2RcV2P_c=I^2R_c=\frac{P^2R_c}{V^2}, this greatly reduces wasted power.

Distinguish a cell’s emf from its terminal voltage when current flows.

Answer: Emf ε\varepsilon is the open-circuit potential difference. When current flows, terminal voltage is lower: V=ε−IrV=\varepsilon-Ir.

Obtain the current supplied by a cell connected to an external resistance.

Answer: Using V=IRV=IR and V=ε−IrV=\varepsilon-Ir, we get I=εR+rI=\frac{\varepsilon}{R+r}.

Quick recap

  • Without collisions, charge carriers gain kinetic energy: ΔK=−ΔUpot=IVΔt\Delta K=-\Delta U_{\text{pot}}=IV\Delta t; collisions transfer this energy to the conductor as heat.
  • Power dissipated in a resistor is P=IV=I2R=V2RP=IV=I^2R=\frac{V^2}{R}.
  • High-voltage transmission reduces cable current and therefore reduces resistive power loss.
  • A cell’s emf is its open-circuit potential difference, not a force.
  • Internal resistance causes terminal voltage to fall to V=ε−IrV=\varepsilon-Ir under load.
  • A cell with external resistance RR supplies current I=εR+rI=\frac{\varepsilon}{R+r}.
Lecture 5

Cells in Series and in Parallel

Reference video · Lecture 5Cells in Series and in Parallel

Cells in Series

Two series-connected cells represented by an equivalent cell.
Two series-connected cells represented by an equivalent cell.
VAC=(ε1+ε2)−I(r1+r2)V_{AC}=(\varepsilon_1+\varepsilon_2)-I(r_1+r_2)
For cells connected so their emfs aid one another, the total terminal voltage is the sum of the individual terminal voltage drops.
Equivalent cell in series
Eeq=E1+E2,req=r1+r2\mathcal{E}_{\mathrm{eq}}=\mathcal{E}_1+\mathcal{E}_2,\quad r_{\mathrm{eq}}=r_1+r_2

For two aiding cells, both emfs and internal resistances add.

Series cells with opposing emfs

  • Opposing connection: If the cells are connected so their emfs oppose, subtract the smaller emf from the larger.
  • Sign rule: Give a cell’s emf a negative sign when the current leaves that cell from its negative terminal.
  • Internal resistance: The equivalent internal resistance remains the sum, regardless of emf directions.
  • Many cells: For nn series cells, add all internal resistances and add emfs algebraically, with signs set by their directions.
Two opposing cells
Eeq=E1−E2,req=r1+r2\mathcal{E}_{\mathrm{eq}}=\mathcal{E}_1-\mathcal{E}_2,\quad r_{\mathrm{eq}}=r_1+r_2

For opposing cells, if ε1>ε2\varepsilon_1>\varepsilon_2, the equivalent emf is the difference.

Cells in Parallel

Two parallel-connected cells represented by an equivalent cell.
Two parallel-connected cells represented by an equivalent cell.
Equivalent cell for two parallel cells
Eeq=E1r2+E2r1r1+r2,req=r1r2r1+r2\mathcal{E}_{\mathrm{eq}}=\frac{\mathcal{E}_1r_2+\mathcal{E}_2r_1}{r_1+r_2},\quad r_{\mathrm{eq}}=\frac{r_1r_2}{r_1+r_2}

The equivalent emf is a resistance-weighted average; the equivalent internal resistance follows the parallel-resistance rule.

1req=1r1+1r2,Eeqreq=E1r1+E2r2\frac{1}{r_{\mathrm{eq}}}=\frac{1}{r_1}+\frac{1}{r_2},\quad \frac{\mathcal{E}_{\mathrm{eq}}}{r_{\mathrm{eq}}}=\frac{\mathcal{E}_1}{r_1}+\frac{\mathcal{E}_2}{r_2}
These equivalent-cell relations can be written using reciprocal resistance and emf per unit resistance.

Parallel cells with opposing emfs

  • Opposite polarity: The reciprocal-resistance relation is unchanged.
  • Emf sign: Use a negative sign for the emf of a cell connected in opposition before applying the parallel-cell relation.
Many cells in parallel
1req=∑i=1n1ri,Eeqreq=∑i=1nEiri\frac{1}{r_{\mathrm{eq}}}=\sum_{i=1}^{n}\frac{1}{r_i},\quad \frac{\mathcal{E}_{\mathrm{eq}}}{r_{\mathrm{eq}}}=\sum_{i=1}^{n}\frac{\mathcal{E}_i}{r_i}

For nn cells, use signed emfs according to their connections; the same equivalent-cell relations apply.

State the rules for equivalent emf and internal resistance when cells are connected in series.

Answer: Add the internal resistances. Add the emfs algebraically, assigning negative signs to cells whose emfs oppose the chosen current direction.

Write the equivalent-cell relations for cells in parallel.

Answer: For nn cells, 1/req=∑i1/ri1/r_{\mathrm{eq}}=\sum_i 1/r_i and Eeq/req=∑iEi/ri\mathcal{E}_{\mathrm{eq}}/r_{\mathrm{eq}}=\sum_i \mathcal{E}_i/r_i, using signed emfs.

Quick recap

  • In series, internal resistances add and emfs add algebraically.
  • Opposing series cells contribute emfs with opposite signs.
  • Parallel cells have the same terminal voltage, and their currents add.
  • For parallel cells, equivalent internal resistance is found by adding reciprocal resistances.
  • The equivalent emf of parallel cells is determined by the sum of emf-to-resistance ratios.
Lecture 6

Kirchhoff’s Rules

Reference video · Lecture 6Kirchhoff’s Rules

Labelling Currents and Cells

Choosing current directions

  • Assumed direction: Assign each branch a current symbol and arrow; the chosen direction may be arbitrary.
  • Interpreting the result: A positive current follows its arrow; a negative current flows opposite to it.
  • Cell labels: Mark each cell’s positive and negative terminals and the assumed current direction through the cell.
Cell terminal voltage
V(P)−V(N)=ε−IrV(P)-V(N)=\varepsilon-Ir

For a cell of emf ε\varepsilon and internal resistance rr, the terminal voltage depends on the direction of current through the cell.

Cell sign convention

  • Current from NN to PP: V(P)−V(N)=ε−IrV(P)-V(N)=\varepsilon-Ir.
  • Current from PP to NN: V(P)−V(N)=ε+IrV(P)-V(N)=\varepsilon+Ir.

Kirchhoff’s Junction Rule

Definition

Junction rule — At any junction, the total current entering equals the total current leaving.

Current conservation
∑Iin=∑Iout\sum I_{\text{in}}=\sum I_{\text{out}}

Apply this relation at a junction or any point along a line.

Why it holds

  • Reason: In steady currents, charge does not accumulate at a junction or along a wire.
  • Consequence: The rate of charge flowing in must equal the rate flowing out.
Circuit illustrating Kirchhoff’s junction rule and loop equations.
Circuit illustrating Kirchhoff’s junction rule and loop equations.

Kirchhoff’s Loop Rule

Definition

Loop rule — The algebraic sum of all potential changes around any closed loop is zero.

Potential changes around a loop
∑closed loopΔV=0\sum_{\text{closed loop}}\Delta V=0

Use signed potential rises and drops while traversing a closed loop.

Why it holds

  • Reason: Electric potential depends on position, so returning to the starting point gives zero net change in potential.
  • Application: Write an equation for each needed junction and closed loop to solve for unknown currents and potential differences.
Kirchhoff’s rules applied to a multi-branch circuit network.
Kirchhoff’s rules applied to a multi-branch circuit network.

Applying the Rules to Networks

Circuit analysis

  • Simple networks: Series/parallel resistor formulas may not be enough for complicated interconnected circuits.
  • Symmetry: A symmetric network can simplify the current distribution, but not every circuit has this advantage.
  • General networks: Apply the junction and loop rules in sufficient independent equations to determine the unknowns.
A cubic resistor network illustrates symmetry-based current distribution with an applied 10 V battery.
A cubic resistor network illustrates symmetry-based current distribution with an applied 10 V battery.
⚠ Common mistake

A negative calculated current does not mean the result is invalid; it means the actual current flows opposite to the assumed arrow.

State Kirchhoff’s junction rule and its physical basis.

Answer: Current entering a junction equals current leaving it. In steady state, charge does not accumulate there.

State Kirchhoff’s loop rule and its physical basis.

Answer: The algebraic sum of potential changes around a closed loop is zero because potential returns to its starting value.

What does a negative value for an assumed branch current indicate?

Answer: The actual current flows in the direction opposite to the arrow chosen for the assumed current.

Quick recap

  • Assumed currents: Choose arrows freely; a negative answer reverses the actual direction.
  • Junction rule: Total current entering equals total current leaving.
  • Loop rule: Signed potential changes around a closed path sum to zero.
  • Cell voltage: For current from NN to PP, V(P)−V(N)=ε−IrV(P)-V(N)=\varepsilon-Ir; for current from PP to NN, it is ε+Ir\varepsilon+Ir.
  • Network solving: Use enough junction and loop equations to find the unknowns; symmetry may simplify some circuits.
Lecture 7

Wheatstone Bridge

Reference video · Lecture 7Wheatstone Bridge

Bridge Arrangement

Wheatstone bridge with an unknown resistance in one arm and a galvanometer in the other diagonal.
Wheatstone bridge with an unknown resistance in one arm and a galvanometer in the other diagonal.

Balanced Bridge and Balance Condition

R2R1=R4R3\frac{R_2}{R_1}=\frac{R_4}{R_3}
At galvanometer null deflection, the ratios of the resistances in the two arms are equal.

Finding an Unknown Resistance

Unknown resistance in the fourth arm
R4=R3R2R1R_4=\frac{R_3R_2}{R_1}

Use when the bridge is balanced and R4R_4 is unknown.

Definition

Meter bridge — A practical device that applies the Wheatstone bridge principle to measure an unknown resistance.

⚠ Common mistake

Do not confuse the arm ratios: for this labelling, the balance condition is R2/R1=R4/R3R_2/R_1=R_4/R_3.

State the Wheatstone bridge balance condition.

Answer: At null deflection, Ig=0I_g=0 and R2R1=R4R3\frac{R_2}{R_1}=\frac{R_4}{R_3}.

How is an unknown R4R_4 found using a balanced Wheatstone bridge?

Answer: Adjust R3R_3 until the galvanometer shows zero, then calculate R4=R3R2R1R_4=\frac{R_3R_2}{R_1}.

Quick recap

  • A Wheatstone bridge has four resistors, a battery arm and a galvanometer arm.
  • A balanced bridge has zero galvanometer current: Ig=0I_g=0.
  • At balance, I1=I3I_1=I_3 and I2=I4I_2=I_4.
  • The balance condition is R2R1=R4R3\frac{R_2}{R_1}=\frac{R_4}{R_3}.
  • For unknown R4R_4, use R4=R3R2R1R_4=\frac{R_3R_2}{R_1} after null deflection.
  • A meter bridge uses the Wheatstone bridge principle to measure resistance.
Lecture 8

Summary

Reference video · Lecture 8Summary

Electric Current and Electromotive Force

Definition

Electromotive force (emf) — The work done per unit charge by a source in moving charge from lower to higher potential energy; emf is a voltage, not a force.

Emf
ε=WQ\varepsilon=\frac{W}{Q}

Here WW is the work done by the source in transferring charge QQ.

Ohm’s Law and Resistance

Ohm’s law
V=IRV=IR

Applies when the material’s resistance is constant under the conditions considered.

Non-ohmic behaviour
Failure of Ohm’s lawExample
The VV–II relation is nonlinear.A device whose current rises nonlinearly with voltage, even at fixed temperature.
The relation changes with the sign of VV, even for equal ∣V∣|V|.A rectifier combines nonlinear and sign-dependent behaviour.
More than one current–voltage relation is possible.GaAs.

Material form of Ohm’s law

  • Field relation: E=ρj\mathbf{E}=\rho\mathbf{j} for a material obeying Ohm’s law.
  • Criterion: Resistivity must not depend on the magnitude or direction of the applied electric field.
  • Range: Silver and pure or impurity-containing germanium are ohmic only within a range of field strengths; sufficiently strong fields cause departures from Ohm’s law.

Resistance and Resistivity

Resistance of a conductor
R=ρlAR=\rho\frac{l}{A}
Typical resistivity ranges
Material classResistivity / relative rangeExamples
MetalsAbout 10−810^{-8} to 10−6 Ω m10^{-6}\,\Omega\,\mathrm{m}Metals
InsulatorsAbout 102210^{22} to 102410^{24} times greater resistivity than metalsGlass, rubber
SemiconductorsIntermediate range on a logarithmic resistivity scaleSi, Ge
Definition

Temperature coefficient of resistivity — The fractional increase in resistivity per unit temperature increase, in the temperature range where resistivity varies linearly with temperature.

Temperature coefficient
α=1ρΔρΔT\alpha=\frac{1}{\rho}\frac{\Delta\rho}{\Delta T}

For a small temperature change in the linear range.

Charge Carriers, Current Density and Drift

Current density for one carrier type
j=nqvd\mathbf{j}=nq\mathbf{v}_d

Here nn is carrier number density, qq is charge per carrier and vd\mathbf{v}_d is drift velocity.

Current through a uniform cross-section
I=nevdAI=ne v_d A

For electrons, this gives the current magnitude when drift speed is vdv_d and the cross-section is AA.

Drift and charge neutrality

  • Drift velocity: Random collision motion averages to zero; the net drift is due to the applied electric field.
  • Multiple carrier types: Apply j=ρqv\mathbf{j}=\rho_q\mathbf{v} separately to each type, where ρq\rho_q is that type’s charge density.
  • Neutral conducting wire: j=ρ+v++ρ−v−\mathbf{j}=\rho_+\mathbf{v}_+ + \rho_-\mathbf{v}_- and ρ++ρ−=0\rho_++\rho_-=0. Since positive charges are nearly stationary, the current can be nonzero even though the wire’s net charge density is zero.
  • Caution: The relation between current density and charge density times velocity applies to each carrier type, not to the neutral wire’s total charge density.

Microscopic Model of Resistivity

Drift speed and resistivity
vd=eEτm,ρ=mne2τv_d=\frac{eE\tau}{m},\qquad \rho=\frac{m}{ne^2\tau}

Here mm is electron mass, nn is electron number density and τ\tau is the mean time between collisions.

Mobility
μ=vdE\mu=\frac{v_d}{E}

Mobility is the drift speed per unit electric field.

Sources with Internal Resistance

Terminal voltage
I=εR+r,Vext=IR=εRR+rI=\frac{\varepsilon}{R+r},\qquad V_{\mathrm{ext}}=IR=\frac{\varepsilon R}{R+r}

Kirchhoff’s Rules

  • Purpose: Kirchhoff’s rules are used to determine currents and potential differences in complex circuits that cannot be reduced to simple series and parallel combinations.
  • Principles: The junction rule expresses conservation of charge, while the loop rule expresses that the algebraic sum of potential changes around a closed loop is zero.

Wheatstone Bridge

Wheatstone bridge null-point condition
R1R2=R3R4\frac{R_1}{R_2}=\frac{R_3}{R_4}
Physical quantities, dimensions and SI units
QuantitySymbolDimensionsSI unitKey relation or note
Electric currentII[A][A]A\mathrm{A}SI base unit
ChargeQ,qQ, q[TA][TA]C\mathrm{C}
Voltage / potential differenceVV[ML2T−3A−1][ML^2T^{-3}A^{-1}]V\mathrm{V}Work per charge
Electromotive forceε\varepsilon[ML2T−3A−1][ML^2T^{-3}A^{-1}]V\mathrm{V}Work per charge
ResistanceRR[ML2T−3A−2][ML^2T^{-3}A^{-2}]Ω\OmegaR=V/IR=V/I
Resistivityρ\rho[ML3T−3A−2][ML^3T^{-3}A^{-2}]Ω m\Omega\,\mathrm{m}R=ρl/AR=\rho l/A
Electrical conductivityσ\sigma[M−1L−3T3A2][M^{-1}L^{-3}T^3A^2]S\mathrm{S}σ=1/ρ\sigma=1/\rho
Electric fieldEE[MLT−3A−1][MLT^{-3}A^{-1}]V m−1\mathrm{V\,m^{-1}}Electric force per charge
Drift speedvdv_d[LT−1][LT^{-1}]m s−1\mathrm{m\,s^{-1}}vd=eEτ/mv_d=eE\tau/m (magnitude)
Relaxation timeτ\tau[T][T]s\mathrm{s}Mean time between collisions
Current densityjj[L−2A][L^{-2}A]A m−2\mathrm{A\,m^{-2}}Current per area
Mobilityμ\mu[M−1T2A][M^{-1}T^2A]m2 V−1 s−1\mathrm{m^2\,V^{-1}\,s^{-1}}μ=vd/E\mu=v_d/E

Why is V=IRV=IR not, by itself, proof that a device obeys Ohm’s law?

Answer: It can define the resistance at a particular operating point. Ohm’s law requires a linear II–VV relation, so resistance is independent of voltage under the stated conditions.

State Kirchhoff’s junction and loop rules and the conservation law behind each.

Answer: At a junction, incoming current equals outgoing current (conservation of charge). Around a closed loop, the algebraic sum of potential changes is zero (conservation of energy).

Write the Wheatstone bridge balance condition.

Answer: R1/R2=R3/R4R_1/R_2=R_3/R_4.

Quick recap

  • Current is charge passing per unit time; emf is source work per unit charge.
  • Ohm’s law requires a linear II–VV relation with resistance independent of voltage.
  • A conductor’s resistance is R=ρl/AR=\rho l/A; resistivity depends on material conditions.
  • Current density and electron drift link microscopic charge motion to macroscopic current.
  • Collisions give vd=eEτ/mv_d=eE\tau/m and ρ=m/(ne2τ)\rho=m/(ne^2\tau) in the simple metal model.
  • Kirchhoff’s rules express charge and energy conservation in circuits.
  • The balanced Wheatstone bridge satisfies R1/R2=R3/R4R_1/R_2=R_3/R_4.

Physics — ALL CHAPTERS

1

Electric Charges And Fields

View

2

Electrostatic Potential And Capacitance

View

3

Current Electricity

View

4

Moving Charges And Magnetism

View

5

Magnetism And Matter

View

6

Electromagnetic Induction

View

7

Alternating Current

View

8

Electromagnetic Waves

View

1

Ray Optics And Optical Instruments

View

2

Wave Optics

View

3

Dual Nature Of Radiation And Matter

View

4

Atoms

View

5

Nuclei

View

6

Semiconductor Electronics: Materials, Devices And Simple Circuits

View